DESCRIPTION

An internally plasticised, high build, high solids, water based acrylic co‑polymer, incorporating synthetic crumbed rubber particles.

FINISH

Matt

COLOUR

White ‑ may be tinted.

USE

As a non‑skid protective membrane where permanent flexibility is required and is servicable for both internal and external application.

APPLICATION AREA

Where a permanently flexible non‑skid membrane is utilised to be both serviceable and to enhance the decor. For application to most common building substrates such as

Tennis Courts

Pool Surrounds

Patios

Walk Ramps

Geriatric Care Areas

Boat Decks

Recreation Facilities

Steps & Stairs, etc

PROPERTIES & PERFORMANCES

WEATHERING: Excellent. For ultimate results should be topcoated with ENVELON High Gloss Acrylic Finish.

SOLVENT RESISTANCE: Good environmental resistance. Avoid areas of splash, spillage etc.

CHEMICAL RESISTANCE: Good. Resists most chemicalenvironments.

ABRASION RESISTANCE: Good. Resilient membrane.

WATER: Withstands exposure in most conditions. Notrecommended for immersion or areas of ponding.

TEMPERATURE: Application range 100C ‑ 300C film service range50C ‑ 900C cured.

FLEXIBILITY: Very Good.

TECHNICAL DATA

SOLIDS CONTENT: 62% volumetric solids.

RECOMMENDED COVERAGE: 24.8m at 25 microns.

RECOMMENDED FILM BUILD: Minimum dry film thickness 600 microns.

DRYING TIME: To touch 30 minutes ‑ 1 hour. Recoat 2‑4 hours. Figures quoted are based on optimum drying conditions ‑ 25C. Low temperatures andlor high humidity will greatly reduce drying efficiency. In normal conditions 16 hours of drying to attain water resistance and 7 days drying to attain hardness and resistance properties.

APPLICATION METHOD: Brush, Roller or Soft Broom

THINNING: Use clean water in moderation.

SHELF LIFE: Excellent long term storage in unopened containers under proper conditions.

HANDLING: Non‑flammable. Adopt normal painting precautions. PACKAGING: Available in 1,4,10 and 20 litre containers.

SURFACE PREPARATION

STEEL & GALVANISED IRON: All surfaces must be free from grease, oil, rust and flaking material and must be dry. Areas of rust should be treated suitably by either blasting or wire brush power tool then coated with A SUITABLE METAL PRIMER (such as FERONITE PRIMER)and allowed to dry. New surfaces must be thoroughly degreased using DEGREASING SOLVENT, making sure all trace of oil has been removed.

MASONARY SURFACES: Concrete surfaces should be cured for 28 days. All dirt or contaminant should be removed by stiff brushing or water blasting. Acid etching or light blasting may be required to provide a suitable surface profile for adequate adhesion. Porous surfaces should be primed with TREDGRIP 2000 PRIMER,

APPLICATION

TREDGRIP IS THIXOTROPIC. Stir contents thoroughly till smooth.

ROLLER: Select the type of roller for surface finish required.

BRUSHING: Use a wide soft nylon brush (or similar type). Thin the first coat to assist penetration. Apply each coat at right angles to preceeding coat to ensure adequate and even coverage.

WHERE MORE SPECIFIC DETAILS ARE REQUIRED RELATING TO THE APPLICATION OF THIS PRODUCT, CONTACT SHOULD BE MADE WITH DOMINION PLASTIC INDUSTRIES OR AN APPROVED AGENT OR APPLICATOR

PRECAUTIONS

Do not apply to surface for the collection of drinking water, as tainting may occur.

Do not apply when rain is expected or when temperatures could fall below 10C.

Do not apply to loose or powdery surfaces.

SAFETY

Ensure adequate ventilation during use and sufficient air flow for the comfort of operator. Spray painters using this product should comply with State and Federal regulations.

IN BRIEF

NUMBER OF COMPONENTS                 one

COLOUR                                                    white

THINNING                                                  clean water

METHOD OF APPLICATION                    brush, roller or broom

APPLY OVER                                             suitably prepared surface

DRYING TIME                                            see text

SOLIDS CONTENT                                   62% volumetric

THEORETICAL COVERAGE                   24.8 m2/litre @ 25um

RECOMMENDED                                      600 urn minimum

THICKNESS

PACKAGING                                              1,4,10 litre & 20 litre

This product should only be used in accordance with instructions on this Data Sheet, the container label or written instructions from the company. This is not a specification and all information is given in good faith. For application in special conditions, consult Dominion Plastic Industries or an appointed agent for detailed recommendation. The manufacturer warrants that its products have been manufactured under strict control to its normal standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and the mode of application. As the manufacturer cannot supervise the above procedure no warranty as to fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any conditions or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months