46 Chetwynd St., Loganholme, Queensland, 4129, Australia
P07 3806 1944 (+617 3806 1944) F07 3209 7711 (+617 3209 7711)

MATERIAL  SAFETY  DATA  SHEET

SECTION  1.  PRODUCT IDENTIFICATION 

 

UN No.	None Allocated	Hazchem	N/A
DG Class	None Allocated	Poisons Schedule	5
CAS No	Mixture	Pkge Group	III

 

Intended usage

A general purpose epoxy adhesive packaged as two separate components.

Classified as hazardous according to the criteria of Worksafe Australia.

SECTION  2.  INGREDIENTS

SECTION 3.  PHYSICAL & EXPOSURE DATA

Product Exposure Limits

Toxicity and Irritation Data

LD(50) for ingestion (rat) - epoxy resin                   5 gm/kg

LD(50) for ingestion (rat) - amines                         3.5 gm/kg

SECTION 4.  HEALTH HAZARD

No adverse effects are expected if the product is handled in accordance with this safety Data Sheet and with the product label.

Symptoms of Exposure:  Acute and Chronic Effects

Ingestion: 

Strong burning sensation, possible vomiting.  Can result in irritation of the gastrointestinal tract and mucous membranes.  Considered as an unlikely route of entry in commercial/industrial environments.

Eye contact:

The amine hardener component may be severely irritating to the eyes and may burn eye tissue.  High concentrations of vapour may cause irritation.

Skin contact: 

May be irritating to the skin and may be capable of causing allergic skin reactions.  Repeated or prolonged contact may lead to dermatitic effects and may cause sensitisation in some individuals. 

Inhalation: 

The vapour is mildly irritating to the mucous membranes and respiratory tract.  The vapour pressure from these products is very low at ambient temperatures and is unlikely to cause exposure from normal handling.  Frequent or prolonged exposure can cause respiratory irritation and may cause sensitisation in some individuals.  Overexposure symptoms include headache, swelling and congestion of the eyes and sinuses.

Systemic and other effects: 

The ingredients may cause adverse effects including sensitisation.  Symptoms include itching rash and respiratory congestion.

Emergency & First Aid Procedures

Ingestion: 

DO NOT INDUCE VOMITING.  If conscious give water or milk to rinse out mouth and drink.  Provide liquid slowly but as much as casualty will drink.  Transport to hospital or doctor without delay.   Activated charcoal may be helpful.

Eye contact: 

Immediately hold the eyes open and irrigate eyes with running water for at least 15 minutes.  Ensure irrigation under eyelids by occasionally lifting the upper and lower lids.  Transport to doctor or hospital without delay.  Removal of contact lenses after an eye injury should only be undertaken by skilled personnel. 

Skin contact: 

Immediately remove all contaminated clothing including footwear.  Wash affected areas thoroughly with detergent hand cleaner and rinse with plenty of water.  Seek medical attention in event of irritation.

Inhalation: 

Remove to fresh air, lie patient down, keep warm and rested.  If breathing is shallow or has stopped, ensure clear airway and apply resuscitation.  Administer oxygen.  Transport to hospital or doctor.

Notes to physician:  Treat symptomatically.

SECTION 5.  PERSONAL PROTECTION & HANDLING

Protective Equipment

Remove and wash all contaminated clothing and equipment.

Handling Procedures

Handle in well ventilated area.  Always observe conditions of good industrial hygiene and safe working practice.

SECTION 6.  FIRE & EXPLOSION

Stability

Stable for minimum 2 years at room temperature.  Excess heating over long periods will degrade ingredients.  .

Flammability

Products will support combustion if heated but will not spontaneously ignite or explode.

Hazardous Decomposition Products

On burning will emit toxic fumes of oxides of nitrogen, carbon monoxide and carbon dioxide.

Hazardous Polymerisation

Will not occur in absence of contact with reactive elements or unless the separately packed components are mixed in large quantities.  This will cause irreversible polymerization with considerable heat build-up.

Incompatibility

Avoid contact with water, strong acids, alkalis, oxidising materials.

Fire Fighting

Toxic fumes will be evolved when this material is involved in a fire.  Fire fighters must wear full protective clothing and self contained breathing apparatus.

Extinguishing Media

Foam, carbon dioxide, dry chemical powder.

SECTION 7.  STORAGE & TRANSPORT

SECTION 8.  SPILLS  &  DISPOSAL

SECTION 9.  AUTHORISATION

Enquiries 

Please call Boatcraft Pacific 07 3806 1944 ( +617 3806 1944) for how to contact your nearest reseller.

Copyright Boatcraft Pacific Pty. Ltd.